Juniper BGP Convergence Time
Phil Lavin
phil.lavin at cloudcall.com
Wed May 16 16:59:44 UTC 2018
Ask if they will configure BFD for you. I’ve not found many transit providers that will, but it’s worth a shot and it will lower failure detection to circa 1 second.
> On 16 May 2018, at 17:49, Adam Kajtar <akajtar at wadsworthcity.org> wrote:
>
> I could use static routes but I noticed since I moved to full routes I have
> had a lot fewer customer complaints about latency(especially when it comes
> to Voice and VPN traffic).
>
> I wasn't using per-packet load balancing. I believe juniper default is per
> IP.
>
> My timers are as follows
> Active Holdtime: 90
> Keepalive Interval: 30
>
> Would I be correct in thinking I need to contact my ISP to lower these
> values?
>
> An interesting note is when I had both ISPs connected into a single MX104
> the failover was just a few seconds.
>
> Thanks again.
>
>
>
>> On Tue, May 15, 2018 at 8:42 PM Ben Cannon <ben at 6by7.net> wrote:
>>
>> Have you checked your timeouts ?
>>
>> -Ben
>>
>>> On May 15, 2018, at 4:09 PM, Kaiser, Erich <erich at gotfusion.net> wrote:
>>>
>>> Do you need full routes? What about just a default route from BGP?
>>>
>>> Erich Kaiser
>>> The Fusion Network
>>> erich at gotfusion.net
>>> Office: 815-570-3101
>>>
>>>
>>>
>>>
>>>> On Tue, May 15, 2018 at 5:38 PM, Aaron Gould <aaron1 at gvtc.com> wrote:
>>>>
>>>> You sure it doesn't have something to do with 60 seconds * 3 = 180 secs
>> of
>>>> BGP neighbor Time out before it believes neighbor is dead and remove
>> routes
>>>> to that neighbor?
>>>>
>>>> Aaron
>>>>
>>>>> On May 15, 2018, at 9:10 AM, Adam Kajtar <akajtar at wadsworthcity.org>
>>>> wrote:
>>>>>
>>>>> Hello:
>>>>>
>>>>> I'm running two Juniper MX104s. Each MX has 1 ISP connected running
>>>>> BGP(full routes). iBGP is running between the routers via a two port
>> 20G
>>>>> lag. When one of the ISPs fails, it can take upwards of 2 minutes for
>>>>> traffic to start flowing correctly. The router has the correct route in
>>>> the
>>>>> routing table, but it doesn't install it in the forwarding table for
>> the
>>>>> full two mins.
>>>>>
>>>>> I have a few questions if anyone could answer them.
>>>>>
>>>>> - What would a usual convergence time be for this setup?
>>>>> - Is there anything I could do speed this process up? (I tried
>>>> Multipath)
>>>>> - Any tips and tricks would be much appreciated
>>>>>
>>>>> Thanks in Advance
>>>>> --
>>>>> Adam Kajtar
>>>>> Systems Administrator
>>>>> City of Wadsworth
>>>>> akajtar at wadsworthcity.org
>>>>> -----------------------------------------------------
>>>>> http://www.wadsworthcity.com
>>>>>
>>>>> Facebook <http://www.facebook.com/cityofwadsworth>* |* Twitter
>>>>> <https://twitter.com/CityOfWadsworth> *|* Instagram
>>>>> <https://www.instagram.com/cityofwadsworth/> *|* YouTube
>>>>> <https://www.youtube.com/channel/UCymlH-AZgvxTaHtgp3-AmDQ>
>>>>
>>>>
>>
>
>
> --
> Adam Kajtar
> Systems Administrator, Safety Services
> City of Wadsworth
> Office 330.335.2865
> Cell 330.485.6510
> akajtar at wadsworthcity.org
> -----------------------------------------------------
> http://www.wadsworthcity.com
>
> Facebook <http://www.facebook.com/cityofwadsworth>* |* Twitter
> <https://twitter.com/CityOfWadsworth> *|* Instagram
> <https://www.instagram.com/cityofwadsworth/> *|* YouTube
> <https://www.youtube.com/channel/UCymlH-AZgvxTaHtgp3-AmDQ>
More information about the NANOG
mailing list