Native VLAN for Huawei MA5616 DSLAM

Shahab Vahabzadeh sh.vahabzadeh at gmail.com
Tue Aug 13 09:48:12 UTC 2013


Dear Tina,
How can I upgrade the version? main board must change or it can upgrade
with changing software/firmware?
Thank


On Tue, Aug 13, 2013 at 6:29 AM, Tina TSOU <Tina.Tsou.Zouting at huawei.com>wrote:

>  Dear Shahab,****
>
> Thank you for more information.****
>
> CCUB main board doesn’t support native-VLAN setting, only CCUE main board
> supports it, the version should be upgraded to R312 above.****
>
> ** **
>
> Thank you,****
>
> Tina****
>
> ** **
>
> *From:* Shahab Vahabzadeh [mailto:sh.vahabzadeh at gmail.com]
> *Sent:* 2013年8月12日 0:51
> *To:* Tina TSOU; Zharov Oleg; nanog
> *Cc:* Georgi Genov
>
> *Subject:* Re: Native VLAN for Huawei MA5616 DSLAM****
>
>  ** **
>
> Dear Tina,
> Thanks for your reply, ****
>
> I have done the same example you told but there is no native-vlan command
> inside interface eth 0/0.
> here my configuration and version of device, maybe firmare does not
> support it.****
>
> MA5616#display current-configuration
>
> [vlan-config]
>   <vlan-config>
>  vlan 2 smart
>  port vlan 2 0/0 0****
>
> ** **
>
> MA5616#display board 0
>   -------------------------------------------------------------------------
>   SlotID  BoardName  Status           SubType0 SubType1    Online/Offline
>   -------------------------------------------------------------------------
>   0       H831CCUB   Active_normal    EP1A     ASDA
>   1       H835ADLE   Auto_find
>   2       H835ADLE   Auto_find
>   3       H835ADLE   Auto_find
>   4       H835ADLE   Auto_find
>   5       H831PDIA   Normal
>   -------------------------------------------------------------------------
> ****
>
>  ** **
>
> MA5616#display version
>
>   Command:
>           display version
>
>   VERSION : MA5616V800R308C01
>   PATCH   : SPC200 SPH508 HP2108
>   PRODUCT : MA5616
>
>   Mainboard Running Area Information:
>  --------------------------------------------
>   Current Program Area : Area A
>   Current Data Area : Area A
>
>   Program Area A Version : MA5616V800R308C01
>   Program Area B Version : MA5616V800R308C01
>
>   Data Area A Version : MA5616V800R308C01
>   Data Area B Version : MA5616V800R308C01
>  --------------------------------------------****
>
>  ** **
>
> MA5616(config)#interface eth 0/0
>
> MA5616(config-if-eth-0/0)#?
> ---------------------------------------------
>   Command of eth Mode:
> ---------------------------------------------
> auto-neg              Enable/Disable port negotiation
> combo-mode            Switch working mode of COMBO port
> display               Display information
> duplex                Set duplex
> flow-control          Support flow control
> line                  Line test
> mdi                   Line-adaptive function
> mirror                Add mirror
> network-role          Network role
> port                  Set TX optical power threshold
> quit                  Exit from current mode and enter prior mode
> reset                 Clear port statistics
> return                Enter the privileged mode
> shutdown              Deactivate port
> speed                 Rate
> switch                Switch language mode
> traffic-suppress      Set port traffic suppression
> undo                  Negate a command or set its defaults****
>
> ** **
>
> Thanks****
>
> ** **
>
> ** **
>
> On Mon, Aug 12, 2013 at 5:51 AM, Tina TSOU <Tina.Tsou.Zouting at huawei.com>
> wrote:****
>
> Dear all,
> Only for the uplink GE, the native VLAN can be configured, it can not be
> configured for NNI EPON/GPON and UNI DSL port.
>
> //if the uplink port is GE, then configure a new VLAN 2
> huawei(config)#vlan 2
> //add the uplink GE 0/0 0 to VLAN 2
> huawei(config)#port vlan 2 0/0 0
> //change to uplink card interface view
> huawei(config)#interface eth 0/0
> //change native vlan of uplink GE to 2
> huawei(config-if-eth-0/0)#native-vlan 0 vlan 2
>
>
> Thank you,
> Tina****
>
>
> On Aug 11, 2013, at 6:44 AM, "Shahab Vahabzadeh" <sh.vahabzadeh at gmail.com>
> wrote:
>
> > Only these interface's are available under:
> >
> > MA5616(config)# interface ?
> >> adsl
> >> emu
> >> eponnni
> >> eth
> >> gponnni
> >> h248
> >> loopback
> >> meth
> >> null
> >> shl
> >> vdsl
> >> vlanif
> >
> >
> > Thanks
> >
> >
> > On Sun, Aug 11, 2013 at 4:55 PM, Shahab Vahabzadeh
> > <sh.vahabzadeh at gmail.com>wrote:
> >
> >> Dear Georgi,
> >> MA5616 does not have any SCU interface...
> >> What can we do?
> >>
> >>
> >> On Sun, Aug 11, 2013 at 4:17 PM, Georgi Genov <linuxloader at gmail.com
> >wrote:
> >>
> >>> It`s configurable under scu/scuh/giu board
> >>>
> >>> interface scu 0/9
> >>> native-vlan 1 vlan XXXX
> >>> native-vlan 2 vlan YYYY
> >>> or
> >>> interface   giu 0/19
> >>> native-vlan 1 vlan XXXX
> >>> native-vlan 2 vlan YYYY
> >>>
> >>> On 11.8.2013 г. 09:33 ч., Shahab Vahabzadeh wrote:
> >>>
> >>>> Dear Friends,
> >>>> Anybody have idea about changing native vlan on Huawei MA5616 DSLAM?
> >>>> I can not find the correct syntax, there is no option under "interface
> >>>> eth
> >>>> 0/0"
> >>>> Thanks
> >>
> >>
> >> --
> >> Regards,
> >> Shahab Vahabzadeh, Network Engineer and System Administrator
> >>
> >> Cell Phone: +1 (415) 871 0742
> >> PGP Key Fingerprint = 8E34 B335 D702 0CA7 5A81  C2EE 76A2 46C2 5367 BF90
> >
> >
> >
> > --
> > Regards,
> > Shahab Vahabzadeh, Network Engineer and System Administrator
> >
> > Cell Phone: +1 (415) 871 0742
> > PGP Key Fingerprint = 8E34 B335 D702 0CA7 5A81  C2EE 76A2 46C2 5367 BF90
> ****
>
>
>
>
> --
> Regards,
> Shahab Vahabzadeh, Network Engineer and System Administrator
>
> Cell Phone: +1 (415) 871 0742
> PGP Key Fingerprint = 8E34 B335 D702 0CA7 5A81  C2EE 76A2 46C2 5367 BF90**
> **
>



-- 
Regards,
Shahab Vahabzadeh, Network Engineer and System Administrator

Cell Phone: +1 (415) 871 0742
PGP Key Fingerprint = 8E34 B335 D702 0CA7 5A81  C2EE 76A2 46C2 5367 BF90



More information about the NANOG mailing list