Why can't I default Originate?
David Barak
thegameiam at yahoo.com
Tue Jul 8 21:09:19 UTC 2003
As I recall, making changes to a peer-group outbound
policy will require all of the peer-group members to
reset (or at least the peer-group leader). Until that
reset happens, a soft clear to a follower session will
only re-send the output of the previously calcluated
policy.
I seem to remember this as an undocumented feature...
;)
-David Barak
--- Haesu <haesu at towardex.com> wrote:
>
> After you applied default-originate to peer-group,
> have you done soft-clear of your bgp session?
>
> It usually takes a little while for changes in
> config to propagate, unless you force an update
> using soft clear...
>
> -hc
>
> --
> Sincerely,
> Haesu C.
> TowardEX Technologies, Inc.
> WWW: http://www.towardex.com
> E-mail: haesu at towardex.com
> Cell: (978) 394-2867
>
> On Tue, Jul 08, 2003 at 12:43:35PM -0700, Vandy
> Hamidi wrote:
> >
> > Platform:
> > Cisco 7206VXR
> > SW:
> > Version 12.2(15)T2
> >
> > router#sh run | b bgp
> > router bgp 65011
> > no synchronization
> > bgp log-neighbor-changes
> > bgp confederation identifier 12345
> > bgp confederation peers 65001 65021
> > bgp deterministic-med
> > bgp dampening
> > network 1.2.3.0 mask 255.255.255.0
> > neighbor Confed-Peer-Group peer-group
> > neighbor Confed-Peer-Group update-source
> FastEthernet1/1
> > neighbor Confed-Peer-Group next-hop-self
> > neighbor Confed-Peer-Group version 4
> > neighbor Confed-Peer-Group soft-reconfiguration
> inbound
> > neighbor Confed-Peer-Group filter-list 2 in
> > neighbor Confed-Peer-Group filter-list 1 out
> > neighbor 10.1.2.75 remote-as 65001
> > neighbor 10.1.2.75 peer-group Confed-Peer-Group
> > neighbor 10.1.2.75 password 7
> 05211F2C105211F2C1666B
> > neighbor 10.1.2.76 remote-as 65001
> > neighbor 10.1.2.76 peer-group Confed-Peer-Group
> > neighbor 10.1.2.76 password 7
> 05211F2C105211F2C1666B
> > no auto-summary
> >
> >
> > router#conf t
> > Enter configuration commands, one per line. End
> with CNTL/Z.
> >
> > router(config)#router bgp 65011
> >
> > router(config-router)#neighbor 10.1.2.75
> default-originate
> > % Invalid command for a peer-group member
> > router(config-router)#
> >
> > According to Cisco:
> > All members of a peer group must share identical
> outbound announcement policies (such as
> distribute-list, filter-list, and route-map), except
> for default-originate, which is handled on a
> per-peer basis even for peer group members.
> >
> > I've also tried to apply to the peer group. The
> command is accepted, but no default origination of
> 0/0 is advertised to the peer(s).
> > Thanks in advanced for any help,
> >
> > -=Vandy=-
>
=====
David Barak
-fully RFC 1925 compliant-
__________________________________
Do you Yahoo!?
SBC Yahoo! DSL - Now only $29.95 per month!
http://sbc.yahoo.com
More information about the NANOG
mailing list